Vag-com For 2.8l

**mandoh** · 01-24-2006, 04:46 PM

hey does anyone know if a vag-com used on an 06 a4 2.0T quattro will work on a 98 a4 2.8L quattro? i need these codes to go away before inspection, short ram intake set off the check engine for my air flow sensor, air bag light is on and the abs,brake lights are also on!!!!!

blazeS4 · 01-24-2006, 06:06 PM

im sure the vag will work on your car as i work for audi.i can tell you clearing the codes will not help you pass inspection.your brake lt and abs lt are probably a faulty module and will come back on more than likely.but even if you get to the inspection place without any lts on they are able to go into the ecm to ck readiness codes and if there not set they will fail you

**AllWheelGrip** · 01-24-2006, 09:14 PM

if u have the updated software then it should

**mandoh** · 01-25-2006, 01:30 AM

well my friend just bought an 06 a4 2.oT and he installed an intake and it set off a code, so he cleared it, he just bought the vag-com for like $350 and he has it hooked up to his lab top. i'm hopeing it'll work,but if it doesnt, how much would a module cost me?

01-24-2006, 04:46 PM	#1 (permalink)
mandoh Moderator Join Date: Jun 2005 Location: New Jersey Posts: 485 Gallery: (0)	hey does anyone know if a vag-com used on an 06 a4 2.0T quattro will work on a 98 a4 2.8L quattro? i need these codes to go away before inspection, short ram intake set off the check engine for my air flow sensor, air bag light is on and the abs,brake lights are also on!!!!! __________________ Its Better To Lead Than To Follow!!!! 1998 Audi A4 2.8l 30valve=SOLD mods-2.75in. milltek cat/bac exhaust,power adder short-ram intake,Giac ecu flash(awetunning),5%tint rear half,blacked out halo headlights 2007 WR Blue Subaru Wrx Sti mods- 3in.catless T/B exhaust,(invidia g200 cat-bac,v2catless D/P),COBB AP tune on 93oct,18x8.5 gunmetal work emotion cr's,blacked out headlights

01-24-2006, 09:14 PM	#3 (permalink)
AllWheelGrip Super Moderator Join Date: Jun 2005 Posts: 1,725 Gallery: (0)	if u have the updated software then it should __________________ There are many paths to the top of the mountain but the view will always be the same

01-25-2006, 01:30 AM	#4 (permalink)
mandoh Moderator Join Date: Jun 2005 Location: New Jersey Posts: 485 Gallery: (0)	well my friend just bought an 06 a4 2.oT and he installed an intake and it set off a code, so he cleared it, he just bought the vag-com for like $350 and he has it hooked up to his lab top. i'm hopeing it'll work,but if it doesnt, how much would a module cost me? __________________ Its Better To Lead Than To Follow!!!! 1998 Audi A4 2.8l 30valve=SOLD mods-2.75in. milltek cat/bac exhaust,power adder short-ram intake,Giac ecu flash(awetunning),5%tint rear half,blacked out halo headlights 2007 WR Blue Subaru Wrx Sti mods- 3in.catless T/B exhaust,(invidia g200 cat-bac,v2catless D/P),COBB AP tune on 93oct,18x8.5 gunmetal work emotion cr's,blacked out headlights

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Remove Advertisements Sponsored Links
Audi Forum Advertisement

01-24-2006, 06:06 PM	#2 (permalink)
blazeS4 Newbie Join Date: Jan 2006 Posts: 3 Gallery: (0)	im sure the vag will work on your car as i work for audi.i can tell you clearing the codes will not help you pass inspection.your brake lt and abs lt are probably a faulty module and will come back on more than likely.but even if you get to the inspection place without any lts on they are able to go into the ecm to ck readiness codes and if there not set they will fail you

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)